Hand Held Test Units
TEC - Hand Held Test Units

Here you can buy Hand Held Test Units designed specifically for the textile industry.

We have other departments for the following:

Read about how TEC used its products for industrial control systems.

All the products in this Department are available and made to order only. If you have an industrial control problem that requires a solution, contact Roger Hitch by email or phone.

Download the brochure.

!

‘Hand Held’ Pt100 Temperature Probe Simulator / Tester

!
‘Hand Held’ Pt100 Temperature Probe Simulator / Tester

A small robust hand held pt100 industrial temperature probe simulator / tester (practical alternative to a resistance box) for use in fault finding industrial control systems but is not a high specification calibration device. It can be used for checking the operation of temperature probe input circuits in temperature controllers or temperature display devices. Supporting calibrated outputs of, 0°C, 50°C, 100°C, at accuracies of ± 0.26, ±0.3, ± 0.4°C respectively and an uncalibrated variable control over 0-160°C. Measuring L 145mm W 90mm H 50mm with 4mm plug and screw terminals. Leads may be ordered separately below.

Download the manual.

‘Hand Held’ Pt100 Temperature Probe Reader / Tester

!
‘Hand Held’ Pt100 Temperature Probe Reader / Tester

A small PP3 battery powered hand held pt100 industrial temperature probe reader / tester directly showing temperature 0-160°C to 1 decimal place, on a 3½ digit LCD display, for use in fault finding industrial temperature control systems. This is not a high specification calibration device. It can be used for checking the operation of temperature probes driving temperature controllers. Supporting an internal self test calibration check setting of 100°C at an accuracy of ± 0.5°C, it will also indicate low battery condition. Measuring L 145mm W 90mm H 50mm with 4mm plug and screw terminals. Leads may be ordered separately below.

Download the manual.

‘Hand Held’ 4-20mA Current Generator / Regulator

!
‘Hand Held’ 4-20mA Current Generator / Regulator

A small robust hand held current generator / regulator (source and sink) for use in testing industrial control systems using 4-20mA signalling. Supporting top, middle and bottom of range fixed calibrated outputs at 4mA, 12mA and 20mA with 1% accuracy and an uncalibrated variable control over the complete 4-20mA range. With 2 pairs of connection terminals, the unit can be powered by the auxiliary 18V to 30V dc supply (not supplied) via a 3.5mm 2 pole jack plug, the internal 22.5 volt alkaline battery or externally directly over the current loop by the control system under test. Measuring L 145mm W 90mm H 50mm with 4mm plug and screw terminals. Leads may be ordered separately below..

Replacement batteries as shown below can be obtained from the small battery company (checked Jul 2008) or from Cellpack Solutions and are soldered to the products battery leads inside the easily accessible battery compartment at the rear.

Type: Alkaline. Voltage: 22.5 V (and has contacts on each end).

Height: 50.8 mm. Width: 15.9 mm. Length: 26.2 mm.

Also known as: Eveready - Energiser 412, 15F20, BLR122, B122, NEDA 215, ANSI 215, BA 261/U, M2152, Mallory M215, Mallory M122, RCA VS084, Varta V72PX, Burgess U15.

Download the manual

 

‘Hand Held’ AD590 Temperature Probe Simulator / Tester

!
‘Hand Held’ AD590 Temperature Probe Simulator / Tester

A small robust hand held AD590 industrial temperature probe simulator / tester for use in fault finding industrial control systems but is not a high specification calibration device. It can be used for checking the operation of temperature probe input circuits in temperature controllers or temperature display devices that use the AD590 sensor. Supporting calibrated outputs of, 0°C, 50°C, 100°C, at accuracies of ± 0.5, ±0.5, ± 0.5°C respectively and an uncalibrated variable control over 0-160°C. Measuring L 145mm W 90mm H 50mm with 4mm plug and screw terminals. Leads may be ordered separately below.

Download the manual.

Universal Test Lead Set

!

Manufactured by RVFM and obtained from Rapid Electronics Limited catalogue number 17-0750.

An extremely versatile universal test lead set with screw on accessories offering a wide variety of probe/test options.

  • Overall lead length 0.9m
  • Contents:
  • Pair red and black test leads
  • Pair red and black probes
  • 2x pair 4mm connectors
  • 2x pairs red and black crocodile clips
  • Pair spade connectors

These test leads fit all the 4mm hand held products' terminal posts.